| Application | Vertical and Horizontal |
|---|
| Installation Mode | Add-on |
|---|
| Table diameter(mm) | Ø210 |
|---|
| Inner diameter of mandrel sleeve(mm) | Ø40H7 |
|---|
| Diameter of center through hole(mm) | Ø 35 |
|---|
| Table height (Horizontal)(mm) | 270 |
|---|
| Table T-slot width(mm) | 12H7 |
|---|
| Guide block width(mm) | 18h7 |
|---|
| Axis / Rotation | 360° |
|---|
| Axis / Tilt | -110°~+110° |
|---|
| Transmission Mechanisms | Roller Cam |
|---|
| Rotary Axis Transmission Mechanism | Roller Cam |
|---|
| Tilt Axis Transmission Mechanism | Roller Cam |
|---|
| Min. increment(deg.) | 0.001 |
|---|
| Rotation Axis Indexing precision(sec.) | 30 |
|---|
| Rotation Axis Repeatability(sec.) | 6 |
|---|
| Tilt Axis Indexing precision(sec.) | 50 |
|---|
| Tilt Axis Repeatability(sec.) | 8 |
|---|
| Rotation Axis Clamping system(kg/cm²) | Pneumatic (0.6 / 6) |
|---|
| Tilt Axis Clamping system(kg/cm²) | Pneumatic (0.6 / 6) |
|---|
| Rotation Axis Clamping torque(kgf · m) | 294 / 30 |
|---|
| Tilt Axis Clamping torque(kgf · m) | 1128 / 115 |
|---|
| Rotation Axis Sever motor model(FANUC)(Straight shaft without key)(Taper) | αiF8 / βis8 |
|---|
| Rotation Axis Sever motor model(MITSUBISHI)(Straight shaft without key)(Taper) | HG - 104 |
|---|
| Tilt Axis Sever motor model(FANUC)(Straight shaft without key)(Taper) | αiF8 / βis8 |
|---|
| Tilt Axis Sever motor model(MITSUBISHI)(Straight shaft without key)(Taper) | HG - 154 |
|---|
| Rotation Axis Speed reduction ratio | 1 / 60 |
|---|
| Tilt Axis Speed reduction ratio | 1 / 90 |
|---|
| Rotation Max. rotation rate of table(min-1) | 50 |
|---|
| Tilt Max. rotation rate of table(min-1) | 25 |
|---|
| Allowable inertia load capacity (Horizontal)(kg-m²) | 0.59 |
|---|
| Rotation Allowable workpiece load (0˚Horizontal)(kg) | 75 |
|---|
| Rotation Allowable workpiece load (0˚~90˚Tilt)(kg) | 50 |
|---|
| Rotation Allowable thrust load (with rotary table clamping) F (N / kgf) | 7358 / 750 |
|---|
| (Axial)＊1 Rotation Allowable thrust load (with rotary table clamping) FxL (N.m / kgf·m) | 1128 /115 |
|---|
| (Radial)＊2 Rotation Allowable thrust load (with rotary table clamping) FxL (N.m / kgf·m) | 294 / 30 |
|---|
| Driving torque(N.m / kgf·m) | 363 / 37 |
|---|
| Net weight ( sever motor excluded)(kg) | 315 |
|---|
| ＊1 | If a mechanical brake is not used, this value will correspond to the motor's holding torque. |
|---|
| ＊2 | Standard configuration: straight shaft without key. Please inquire for tapered-shaft motor compatibility. |
|---|
| ＊3 | The structural limit value, while the actual operating speed will vary depending on the motor. |
|---|
| ＊4 | Roller gear cam or D.D. rotary tables may lose position after power loss or alarm, causing axis shift at restart. Use a brake motor (cover size may vary). |
|---|
